Search results for "mechanical propertie"
showing 10 items of 241 documents
Quasi-static behaviour and damage assessment of flax/epoxy composites
2015
Experimental investigations were conducted on flax and E-glass fibres reinforced epoxy matrix composites subjected to quasi-static loadings. Flax/epoxy samples having [0]12, [90]12, [0/90]3S and [±45]3S stacking sequences, with a fibre volume fraction of 43% have been tested under tension, compression and in-plane shear loadings. Overall, the compression strength of glass/epoxy was 76% greater than for the flax/epoxy composite. The damage evolution of flax/epoxy of [0/90]3S and [±45]3S samples has been evaluated in terms of transverse crack densities with respect to the load increment. The crack density exhibited a classical “S” shaped pattern for [0/90]3S and linearly for [±45]3S specimens…
Synergistic effect of fiber content and length on mechanical and water absorption behaviors of Phoenix sp. fiber-reinforced epoxy composites
2016
Phoenix sp. fiber-reinforced epoxy composites have been manufactured using compression molding technique. The effect of reinforcement volume content (0%, 10%, 20%, 30%, 40%, and 50%) and size (300 µm particles, 10 mm, 20 mm, and 30 mm fibers) on quasi-static and dynamic mechanical properties was investigated. Moreover, the water absorption properties of composites were analyzed at different environmental conditions (10℃, 30℃, and 60℃). For each reinforcement size, composites loaded with 40% in volume show highest tensile and flexural properties. Furthermore, composites with 300 µm particles present the best impact properties and the lowest water absorption, regardless of the environmental …
Fibre extraction from oleaginous flax for technical textile applications: influence of pre-processing parameters on fibre extraction yield, size dist…
2017
International audience; Cultivated primarily for its seeds, oleaginous flax could also be valued for the different fractions that can be extracted from the straw. However, as the straws are not harvested with the same technique and care than for the textile flax, the classical scutching technique cannot be used. As a consequence, an “all fibre” device was used to perform the separation of the different constituents of the oleaginous flax straws. The different fractions were quantified for two retting levels and for two degrees of rewetting of the stems. The physical and mechanical properties of fibres were then evaluated. It appears that the relative amount of fibres extracted from oleagino…
The impact of ocean acidification and warming on the skeletal mechanical properties of the sea urchin Paracentrotus lividus from laboratory and field…
2015
AbstractIncreased atmospheric CO2 concentration is leading to changes in the carbonate chemistry and the temperature of the ocean. The impact of these processes on marine organisms will depend on their ability to cope with those changes, particularly the maintenance of calcium carbonate structures. Both a laboratory experiment (long-term exposure to decreased pH and increased temperature) and collections of individuals from natural environments characterized by low pH levels (individuals from intertidal pools and around a CO2 seep) were here coupled to comprehensively study the impact of near-future conditions of pH and temperature on the mechanical properties of the skeleton of the euechin…
Conifer Needles as Thermoplastic Composite Fillers: Structure and Properties
2016
This study describes the properties of thermoplastic polymer composites based on polyethylene (of low and high density) and ethylene-propylene copolymers using various types of conifer needles (pine, spruce, fir, and cedar) as fillers. For the needles, thermogravimetric analysis (TGA) and TGA/Fourier transform infrared spectroscopy (TGA/FTIR) were performed to investigate their structures and thermal resistance, as required for the composite processing methods. Moreover, structural differences were studied for the analyzed fillers and composite materials (FTIR). The results were compared with the values obtained for composites with conifer wood flour. Composites with conifer needles (pine) …
Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt…
2019
A butt joint configuration of AA6061–pure Ti was welded using friction stir welding (FSW) with an assisted cooling and heating conditions, aiming to attain a flawless joint. Cooling-assisted friction stir welding (CFSW) was carried out with a different cooling medium such as CO2, compressed air and water at controlled flow rate. However, heating-assisted friction stir welding (HFSW) was performed with heating source of GTAW torch just before FSW tool at different current density. Prepared specimens were subjected to optical microscopy (OM), scanning electron microscopy (SEM) and electrodischarge spectroscopy (EDS) for microstructural characterizations. The tensile strength and microhardness…
Microstructural, mechanical and energy demand characterization of alternative WAAM techniques for Al-alloy parts production
2020
Abstract Additive manufacturing (AM) processes are gathering momentum as an alternative to conventional manufacturing processes. A research effort is being made worldwide to identify the most promising AM approaches. Within this category, wire arc additive manufacturing (WAAM) is among the most interesting, especially when large parts must be manufactured. In this paper, two different WAAM deposition techniques suitable for the deposition of Aluminum alloys, Cold Metal Transfer (CMT) and CMT mix drive, are analyzed and compared. With the aim of obtaining a clear picture concerning the two different techniques, microstructural analyses, mechanical property evaluation and electrical energy de…
Large strain stimulation promotes extracellular matrix production and stiffness in an elastomeric scaffold model
2016
Mechanical conditioning of engineered tissue constructs is widely recognized as one of the most relevant methods to enhance tissue accretion and microstructure, leading to improved mechanical behaviors. The understanding of the underlying mechanisms remains rather limited, restricting the development of in silico models of these phenomena, and the translation of engineered tissues into clinical application. In the present study, we examined the role of large strip-biaxial strains (up to 50%) on ECM synthesis by vascular smooth muscle cells (VSMCs) micro-integrated into electrospun polyester urethane urea (PEUU) constructs over the course of 3 weeks. Experimental results indicated that VSMC …
Microwear textures associated with experimental near-natural diets suggest that seeds and hard insect body parts cause high enamel surface complexity…
2022
In mammals, complex dental microwear textures (DMT) representing differently sized and shaped enamel lesions overlaying each other have traditionally been associated with the seeds and kernels in frugivorous diets, as well as with sclerotized insect cuticles. Recently, this notion has been challenged by field observations as well as in vitro experimental data. It remains unclear to what extent each food item contributes to the complexity level and is reflected by the surface texture of the respective tooth position along the molar tooth row. To clarify the potential of seeds and other abrasive dietary items to cause complex microwear textures, we conducted a controlled feeding experiment wi…
Green Composites Based on PLA and Agricultural or Marine Waste Prepared by FDM
2021
Three dimensional-printability of green composites is recently growing in importance and interest, especially in the view of feasibility to valorize agricultural and marine waste to attain green fillers capable of reducing bioplastic costs, without compromising their processability and performance from an environmental and mechanical standpoint. In this work, two lignocellulosic fillers, obtained from Opuntia ficus indica and Posidonia oceanica, were added to PLA and processed by FDM. Among the 3D printed biocomposites investigated, slight differences could be found in terms of PLA molecular weight and filler aspect ratio. It was shown that it is possible to replace up to 20% of bioplastic …